Almost everyone maintains their own individual opinion with regards to Installing A Bathtub.
Installing a bathtub isn't specifically brain surgery, yet it does call for solid plumbing, woodworking, as well as often, tiling abilities. Replacing an old tub with a new one is additionally a reasonably challenging job. If the old tub is readily available, the job can relocate easily; if you need to open up a wall surface to remove the old bathtub and position the brand-new bath tub, the task is a lot harder. In either case, the task is within a home handyman's skills, although you will need a helper to vacate the old tub and embeded in the new one. See to it you have certified yourself for the task and also fit attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is much better to consider employing one before you start. Chances are you may require a specialist plumber to make tube links.
This write-up will certainly aid you install a new tub in your shower room if you have actually currently purchased a new bathtub and also don't need to change the arrangement of your previous water pipes.
Your tools and also product list ought to comprise the following:
Preparing for the Installation
First of all, the supporting framework supplied with the bath ought to be fitted (if called for) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to make sure that if the faucet features a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps system to stop stress on the tub.
Fit the flexible faucet ports to the bottom of both faucets utilizing 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its final placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you ought to do is disconnect the supply of water. After doing so, activate the faucets to drain pipes any water remaining in the system. The process of removing the existing taps can be quite problematic as a result of the restricted access that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a cloth prepared for the continuing to be water that will come from the pipelines. As soon as the supply pipes have actually been eliminated, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Prior to carrying on to fit the new faucets, compare the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Installing the Bath tub
Using the two wooden boards under its feet, put the bath tub in the called for position. The wooden boards are helpful in equally spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 small points.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by examining the spirit level as well as changing the feet on the tub till the spirit level reviews level.
To install faucets, fit the bottom of the outermost versatile tap port to the proper supply pipe by making a compression join; then do the exact same for the other tap.
Activate the water supply and examine all joints as well as new pipework for leaks and also tighten them if required. Load the tub and additionally check the overflow electrical outlet and the normal electrical outlet for leaks.
Lastly, repair the bathroom paneling as described in the manufacturer's instruction manual. Tiling as well as sealing around the bath tub needs to wait up until the tub has been utilized at the very least once as this will certainly resolve it into its last setting.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly need a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the tap and also the other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washing machines are in location between the faucet and also the sink. Protect the faucet in position with the producer given backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet adapters. The previous type needs to be linked to the tap ends initially, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bath meets the tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to fracture an inflexible seal, causing the water to permeate the wall surface between the bath and also the tiling, leading to issues with dampness as well as possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your fixtures as well as fittings. They are marketed in tubes as well as cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Remember to always load the tub with water before securing, to permit the motion experienced when the tub is in usage. The sealant can split rather early if you do not take into consideration this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently available on the market. It is recommended to fit the tiles making use of waterproof or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was guided to that write-up about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through an associate on a different web property. Enjoyed our blog posting? Please share it. Let someone else locate it. Thank-you for going through it.
Top-notch service? Dial here.